Embedded module TQMP2020 – with Freescale QorIQ™ P2
Embedded module TQMP2020 - with Freescale QorIQ™ P2
ower Architecture module with Freescale QorIQ™ P2020 processor
Key functionalities :
- Easiest migration of PowerQUICC III on QorIQ™ by approved e500v2 core
- Single (P2010)- and MultiCores (P2020) of 400 up to 2x 1200 MHz in 45nm SOI for best Performance/Watt ratio
- High-Speed communication via 3x Gigabit Ethernet, 3x PCIe and one USB 2.0 interface
- Simple function extension via PCIe, SPI, I²C and flexible local bus
P2020 Dual Core / 2×1000 MHz, 128 MB NOR Flash, 512 MB DDR III, 32 kbit EEPROM,
Extended temperature range from -40°C…+85°C
Request price information
The embedded module TQMP2020 manufactured by TQ is the next generation of the well-known PowerQUICC III module family TQM85xx. The TQMP2020 is based on the P2020 dual core communications processor. The Freescale QorIQ™ processor family P1 and P2 opens up the possibility of new applications in industry and communications. With one or two e500 cores and a clock speed ranging from 400 MHz to 2x 1200 MHz, the TQ module with its QorIQ™ processors offers an optimal balance between data processing speed and power dissipation. Thanks to the 45nm technology employed, power consumption is markedly lower that in comparable PowerQUICC III modules. This along with the extended temperature range means that it can be fitted to fanless systems.
The TQ minimodule TQMP2020 is ideally suited to industrial applications where long-term availability, outdoor ambient temperatures and small sizes are important factors. In this respect, the module provides an excellent basis for quick and efficient networking by means of interfaces such as Gigabit Ethernet, PCIe and USB 2.0.
CPU frequency: up to 1200 MHz
Microprocessor: Dual (P1020/P1021/2020) or single (P1011/P1012/P2010) high-performance Power Architecture e500v2 cores
EEPROM: 32 KByte
NOR-Flash: 128 MB
supports to boot from the flash card
SDRAM: up to 2 GB
Gigabit Ethernet: 3x
with Jumbo Frame Support, IP checksums calculation and IEEE1588v2 support
I²C: 2x, max. 400 kHz
RS232: DUART, max. 115 kBaud
USB: 1x USB 2.0 HOST with ULPI interface
Other interfaces & busses
Debugging: JTAG Interface
GPIO: Up to 16
Local bus frequency: 16 bit enhanced / up to 66 MHz
PCIe: 3x (2x)
1.0a controller up to 2,5 Gbit/s
RapidIO: up to 2x serial
with integrated message unit up to 3,125 Gbit/s
Dimensions: 74mm x 54mm
Power consumption: typ. 5 up to 7 W
Pin number: 360
Plug system: 0.8mm
Power supply: 3,3 V
Temperature range: 0°C … +70°C
Temperature range, extended: -40°C … +85°C
Availability: In production
Operating systems / User interfaces
Operating systems: Linux, QNX
Operating systems on request: VxWorks
At TQ you not only get first-class embedded systems – we also provide a series of benefits around the embedded module:
We support you in defining your requirements for your project. The technical specification serves as guideline for all persons that are involved in the development process.
For a fast and easy starting-up we provide starter kits. Through the plug-and-play principle, the software evaluation can be started, if the actual target hardware is not yet available. Due to this a product can be launched faster, reasonably priced and more safely.
We support you concerning the selection of components as well as Obsolescence management. Thus your products are protected against obsolete components, complex redesigns, doubtful sources and cost-intensive brokerwares.
If desired we arrange a circuit diagram review for your baseboard directly by the developer of the module. Due to the longtime experience of our developers, it happens quite often that entrapments are indentified in the course of the review.
Supply of Software, especially Board Support Packages and hardware-close driver for the required operating system. Therefore you shorten your development time and reduce your costs.
Starting-up of your baseboard. In case that the starting-up of your baseboard with our module does not work at once, we support you by a structural fault analysis in order to quickly find the reason and repair it.
We provide you with reference notes to power-on’s e.g. power-on of a CAN controller to the local bus, as well as with application notes.
Our Field Application Engineers are pleased to assist you with words and deeds before, during and after your design phase
As system service provider TQ is able to take over the development, production and test of your baseboard. Therefore you get the whole tested unit from one hand.
Please just ask us. We are pleased to consult you!
STKP2020 BStarterkit baseboard STKP2020 - for TQ modules based on QorIQ P-Series
valuation platform for TQMP20xx and TQMP10xx
- 2x PCIe (x1) upgrading plug-in positions for e.g.
– PCIe-to-SATA cards
– Graphic cards
- 3x Gigabit Ethernet ports for maximum I/O performance with IEEE1588 support for synchronism intime of shared systems in nano seconds range
- Shunts for measuring the power consumption of the module, PCIe slots and of the baseboard. This enables an easy estimation of the power requirement and therefore the dimensioning of the cooling connection in the application
The baseboard STKP2020 supports all modules of the type series TQMP20xx and TQMP10xx and represents a universal platform for evaluation and development of customer specific platforms for those modules.
SDHC: For data systems or for data logging (bootable) up to 32 GB
Ethernet 1000BaseT: 3x
SPI: 1x with four chip selects
USB: 1x USB 2.0 HOST
Other interfaces & busses
GPIO: Up to 16 signals
PCI: 2x (x1 Interface) 1.0a compliant
JTAG/BDM: COP/JTAG interface for easy Debugging with BDI2000 oder Lauterbach
Dimensions: 240mm x 170mm
DIP switches: 12x
Buffer battery: Yes, for RTC buffering
Reset button: Yes
Power supply: 18 V
Status LED: 16x
Temperature range: 0°C … +70°C
Availability: In Production