The TQMT1042 embedded module embodies the next generation of the well-known TQMP1020/2020 QorIQ™ product family. The QorIQ™ T1 processor family inaugurates new applications in industry and communications.
With four e5500 (64-bit) cores and a clock rate of up to 4x 1400 MHz, the TQ modules using QorIQ™ processors provide the best ratio between processing speed and power loss. The 28 nm technology significantly reduces the power consumption compared to a QorIQ™ module of the former generation.
This feature, together with the expanded temperature range and intelligent power management, enables the use in fan-free systems. The TQMT1042 is best suited for industrial applications that demand high availability, outdoor ambient temperatures and small overall size.

Microprocessor

CPU frequency: up to 1200 MHz
Microprocessor: Dual (P1020/P1021/2020) or single (P1011/P1012/P2010) high-performance Power Architecture e500v2 cores
Memory

EEPROM: 32 KByte
NOR-Flash: 128 MB
SDHC: 1x
supports to boot from the flash card
SDRAM: up to 2 GB
System interfaces

Gigabit Ethernet: 3x
with Jumbo Frame Support, IP checksums calculation and IEEE1588v2 support
I²C: 2x, max. 400 kHz
RS232: DUART, max. 115 kBaud
SPI: 1x
USB: 1x USB 2.0 HOST with ULPI interface
Other interfaces & busses

Debugging: JTAG Interface
GPIO: Up to 16
Local bus frequency: 16 bit enhanced / up to 66 MHz
PCIe: 3x (2x)
1.0a controller up to 2,5 Gbit/s
RapidIO: up to 2x serial
with integrated message unit up to 3,125 Gbit/s
General

Dimensions: 74mm x 54mm
Power consumption: typ. 5 up to 7 W
Pin number: 360
Plug system: 0.8mm
RoHS: Yes
RTC: Yes
Power supply: 3,3 V
Temperature range: 0°C … +70°C
Temperature range, extended: -40°C … +85°C
Availability: In production
Watchdog: Yes
Operating systems / User interfaces

Operating systems: Linux, QNX
Operating systems on request: VxWorks

At TQ you not only get first-class embedded systems – we also provide a series of benefits around the embedded module:

We support you in defining your requirements for your project. The technical specification serves as guideline for all persons that are involved in the development process.

For a fast and easy starting-up we provide starter kits. Through the plug-and-play principle, the software evaluation can be started, if the actual target hardware is not yet available. Due to this a product can be launched faster, reasonably priced and more safely.

We support you concerning the selection of components as well as Obsolescence management. Thus your products are protected against obsolete components, complex redesigns, doubtful sources and cost-intensive brokerwares.
If desired we arrange a circuit diagram review for your baseboard directly by the developer of the module. Due to the longtime experience of our developers, it happens quite often that entrapments are indentified in the course of the review.

Supply of Software, especially Board Support Packages and hardware-close driver for the required operating system. Therefore you shorten your development time and reduce your costs.

Starting-up of your baseboard. In case that the starting-up of your baseboard with our module does not work at once, we support you by a structural fault analysis in order to quickly find the reason and repair it.

We provide you with reference notes to power-on’s e.g. power-on of a CAN controller to the local bus, as well as with application notes.

Our Field Application Engineers are pleased to assist you with words and deeds before, during and after your design phase.

As system service provider TQ is able to take over the development, production and test of your baseboard. Therefore you get the whole tested unit from one hand.

Please just ask us. We are pleased to consult you!